db-derby-commits mailing list archives

Site index · List index
Message view « Date » · « Thread »
Top « Date » · « Thread »
From Apache Wiki <wikidi...@apache.org>
Subject [Db-derby Wiki] Update of "BuildingDerby" by JohnHEmbretsen
Date Wed, 28 Feb 2007 14:20:07 GMT
Dear Wiki user,

You have subscribed to a wiki page or wiki category on "Db-derby Wiki" for change notification.

The following page has been changed by JohnHEmbretsen:
http://wiki.apache.org/db-derby/BuildingDerby

The comment on the change is:
Added info on the NetBeans Subversion module

------------------------------------------------------------------------------
  
  This section describes how to checkout and build Derby using [http://www.netbeans.org/ NetBeans
5.5]. (Similar steps should work on other !NetBeans versions as well, though there will most
likely be some differences).
  
- Steps 1 and 2 below describe checking out the Derby source code with Subversion from within
!NetBeans. If you would rather like to build source code obtained by other means (for example
distributed as an official release), or you have already checked out the source, proceed to
Step 3.
+ Steps 1, 2 and 3 below describe checking out the Derby source code with Subversion from
within !NetBeans. If you would rather like to build source code obtained by other means (for
example distributed as an official release), or you have already checked out the source, proceed
to Step 4.
- 
+   
    1. Install Subversion
  
      Set up Subversion on your machine if you have not already done so. This is described
in the !NetBeans 5.5 IDE help under "''IDE basics''"->"''Working with Subversion''". 
  
+   1. Install !NetBeans' Subversion module (!NetBeans 5.5 only)
+ 
+     Visit the Update Center ("''Tools''"->"''Update Center''") and download the Subversion
module listed in the Version Control category. If you are using !NetBeans 6 (dev), you already
have this module. If you are using !NetBeans 5.0 or earlier, you cannot use the IDE to checkout
Derby.
+ 
    1. Check out the Derby source code
  
-     '''Note:''' If you have already checked out the Derby repository outside of the IDE,
!NetBeans will automatically recognize the files as being under version control; proceed to
step 3. 
+     '''Note:''' If you have already checked out the Derby repository outside of the IDE,
!NetBeans will automatically recognize the files as being under version control; proceed to
step 4. 
  
      I. Use the "''Subversion''"->"''Checkout...''" menu item. Enter the URL for the repository
(folder) you want to check out in the "''Repository URL''" field. Normally this would be the
URL for the latest development trunk, https://svn.apache.org/repos/asf/db/derby/code/trunk/.
If you want to build a specific branch instead, you may browse to the desired folder after
clicking the "''Next''" button, or you may specify the branch URL directly (see [http://db.apache.org/derby/dev/derby_source.html#Derby+source+code
the Derby web site] for further info). Leave the user and password fields blank (unless you
are a committer and want to commit patches using !NetBeans' Subversion interface). Enter your
proxy information if you are using a proxy to connect to the Internet. Click "''Next''".
  
@@ -118, +122 @@

  
      If your Derby project is not set as main project, right-click your Derby project and
select "''Build Project''".
  
-     If the build fails, right-click the Derby project and select "''Clean Project''" before
you try again (after fixing the issues (errors) reported) - or run "''Clean and Build Project''"
instead on the next try. If you get an error message complaining about not finding ant classes,
revisit Step 4. Warnings can be ignored. The "''BUILD SUCCESSFUL''" message indicates that
all went well.
+     If the build fails, right-click the Derby project and select "''Clean Project''" before
you try again (after fixing the issues (errors) reported) - or run "''Clean and Build Project''"
instead on the next try. If you get an error message complaining about not finding ant classes,
revisit Step 5. Warnings can be ignored. The "''BUILD SUCCESSFUL''" message indicates that
all went well.
  
    1. Build the Derby jars (optional)
  
-     Right-click your Derby project and select the label you created in Step 5. Depending
on the settings in your ant.properties file, the Derby jars will end up in the jars/sane/
or the jars/insane/ directory.
+     Right-click your Derby project and select the label you created in Step 6. Depending
on the settings in your ant.properties file, the Derby jars will end up in the jars/sane/
or the jars/insane/ directory.
  
    1. Congratulations, you have now built Derby! Now it's time to update the "Output" and
"Java Sources Classpath" properties of your Derby project if needed for code completion, debugging,
etc. and start hacking some Derby code (or create tests, or review code, or...)!
  

Mime
View raw message